Cancel the staple feature or reset the documents with the same width.005-210005-275005-280005-283005-284005-285005-286 An error occurred in the document feeder. Contact the Xerox Welcome Center if the problem persists. 016-704 The hard disk ran out of space, because the mailboxes are full. The destination machine may be set not to send its own ID number. If none of those solutions address the problem on your machine please consider contacting your local support centre. http://jamisonsoftware.com/error-code/fuji-xerox-printer-error-codes.php
If this does not help please consider contacting your support centre. All rights reserved. Cheryl Otstott October 16, 2014 at 4:23 pm - Reply Hi David, Thank you for reading the At Your Service blog. Contact the Xerox Welcome Center if the problem persists. 016-210 An error occurred on the software option settings.
An attribute value specified violates some constraint. Try one of the following:Check that the correct paper size is loaded in the machine. Notify your System Administrator. The only potential solution for the ROS Fault is to turn off the machine wait a full 2 minutes and then power the machine back on.
Check the LDAP server authentication settings. 018-749 An LDAP server protocol error occurred in the address book operation. Ask the other party to check their machine status, and resend the document if necessary. 035-704 The specified feature (such as polling) is not supported by the remote machine. User has insufficient access to perform the operation. Fuji Xerox Error Code 116-324 The server returned the RFC2251 specification protocol error 4 (size limit exceeded) during the address book query.
Contact the Key Operator. 027-754 The settings for [DocuWorks Signature] or [PDF Signature] on the job flow are incorrect. Xerox Workcentre 7345 Error Code List Pdf If a speed dial button was used, check the correct number is registered appropriately. 034-728 An invalid number was specified. Check the LDAP server status. 018-791 An LDAP server protocol error occurred in the address book operation. https://atyourservice.blogs.xerox.com/2013/02/26/fault-error-problem-codes-lets-fix-them/ This error was generated by the software.
Remove and re-install the Fuser. Xerox Colorqube Error Codes The server certificate is not yet valid. Reset the settings of mailbox print and sample print. Unfortunately I can not find anything about the error message you are seeing.
Directly enter thereduction/enlargement ratio, or change the paper size.003-981Stapling mixed size documents is available only for documents with the samewidth. Please make sure that you have pressed stop before programming your copy job to clear any instructions in the machine. Xerox Workcentre 7345 Error Code List The server returned the RFC2251 specification protocol error 49 (invalid credentials) during the address book query. Xerox Printer Error Helpful Resources Helpful Resources How do i resolve this Cheryl Otstott March 22, 2016 at 3:43 pm
How do i resolve this Cheryl Otstott March 22, 2016 at 3:43 pm- Reply Hi Darren, Thank you for your comment. http://jamisonsoftware.com/error-code/ge-error-codes.php Reduce the document size using [Reduce/Enlarge]. Make sure that the DNS server connection and the domain name are registered to the DNS server. 027-745 The address of the DNS server is not registered on the machine. The server returned the RFC2251 specification protocol error 11 (admin limit exceeded) during the address book query. Xerox C75 Fault Codes
Check the LDAP server status. 018-794 An LDAP server protocol error occurred in the address book operation. If receiving, ask the other party to resend the document if necessary. 035-727 035-728 035-729 A communication error occurred. Check from CentreWare Internet Services to see if the SMTP server is set correctly. 027-501 Unable to resolve the name of the POP3 server when using the POP3 protocol. http://jamisonsoftware.com/error-code/fuji-xerox-error-code-list.php I have followed the initial instruction such as power off / on for over 30 minutes, but error keep displaying.
Thanks, CherylO-Xerox David October 15, 2014 at 2:11 pm - Reply I have a Xerox WC7845, I am trying to use it to fax from my desktop. Xerox Error Codes Phaser 8560 Perform the same operation again. Wait a while and perform the same operation.
The Auto Tray Switching feature was enabled when [Auto Paper Off] is selected for all paper trays on the [Paper Type Priority] screen. If DP (Dial Pulse) is used for G3, check that “” and “#” are not included in the phone number. 035-702 035-703 The other party cancelled the transmission. Thanks, CherylO-Xerox Patrick Nobili October 26, 2015 at 10:28 am - Reply Does anyone know what the fault code 099-395 is on a Versant 2100? Xerox 5755 Error Codes List Turn the printer off, then on.
Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the power off and on. The SMB server is operating in share security mode. check my blog Delete unnecessary documents from the mailboxes. 016-705 Unable to register the secure print document, mailbox document, or billing data using the print driver, or unable to register the scanned document in
Turn the printer off, then on. An SSL client certificatecould not be acquired. Contact the Xerox Welcome Center if the problem persists. 033-736 The transmission was canceled, because the transmit data size exceeded its upper limit. The operation is not allowed on an RDN (update-related problem).
The server returned the RFC2251 specification protocol error 6 (compare true) during the address book query. Do not power down until the power down massage appear 2 message show communication error. Reinstall the media. Rose Anne Cheryl Otstott March 7, 2016 at 5:53 pm - Reply Hi Rose Anne, Thank you for writing a comment and for reading the At Your Service blog.
Both of the codes indicate a communications error. Thanks, CherylO-Xerox Cristi December 5, 2013 at 1:23 am - Reply Dear Support, We have a Xerox ColorQube 9201 and the message still displays17-570-00 Network Time Protocol (NTP) communication error; machine Check the LDAP server status. 018-734 An LDAP server protocol error occurred in the address book operation. Thanks, CherylO-Xerox Sanjay Barad February 6, 2016 at 6:40 am - Reply Hiii My Xerox Workcentre 7345 Error is 004-361 pls help me Cheryl Otstott February 15, 2016 at 5:34 pm