The accuracy of values over 2.500 OD is limited as described below. (Note that some cuvette based spectrophotometers are only specified for accuracy to 1.0 OD, but can read up to Yes, there are certain chemicals that may have a damaging effect on some parts of a liquid handler. How do I import data into Gen5? Please try the request again. http://jamisonsoftware.com/error-codes/fortran-90-error-codes.php
Your cache administrator is webmaster. How can I get Vista compatible USB drivers for my system? Your Universal Test Plate comes with a tri-fold paper listing absorbance values at different wavelengths for your plate. (example below) These will be referred to as the "target" values. Why is the OD accuracy, linearity and precision specified for a smaller range than the defined dynamic range?
When handling the filters, keep the surfaces clean from fingerprints and debris by simply wiping with a lens tissue or other lint free cloth How are BioTek readers able to read This and other factors (such as bulb strength, ambient blocking etc.) do not allow the readers to always have the best results above a specific value. What is AutoPrime™ and when should I use it? When Gen5 is installed on a computer that is not connected to the plate reader, you should set the "System:Reader Configuration" as though your exact model BioTek plate reader were attached.
O-rings on the Precision Microplate Pipetting System should be replaced at least every six months for continued dispense accuracy and precision. COM 1). 3) Confirm that the serial cable and/or USB-serial adapter was obtained from BioTek. Drivers included with the instruments and the adapter are only compatible with Microsoft Windows XP and lower. Biotek Gen5 Manual Keyword Product 405 LS Washer405 TS WasherBioSpa 8 Automated IncubatorBioStack Microplate StackerCytation 3 Cell Imaging Multi-Mode Reader Cytation 5 Cell Imaging Multi-Mode Reader Cytation Multi-Mode Reader EL406 Washer DispenserELx405 Select Deep
For most applications, weak acids and bases can be used. Biotek Elx800 Manual I am currently using a BioTek 405 plate washer and am having some clogging issues with the aspiration manifold. In Gen5, go to System > Instrument Control and (1) go to the Pre-heating tab to set a temperature and turn the incubator on or (2) go to the Tungsten Lamp Start a new Gen5 Experiment using the protocol designed in Step 1, and click on “Read plate,” choose “Read from File” and browse to find the stored *.txt file to import.
You have AutoPrime™ enabled. Next run a liquid test where the higher values are closer to the sample values that you want to use. Can I use pathlength correction wavelengths other than 977 nm for aqueous solutions? The system returned: (22) Invalid argument The remote host or network may be down.
What is the best way to store ELx800 and ELx808 interference filters for extended periods of time? This plate has almost no background in the UV range, and therefore is ideal for reading absorbance of samples in this range. Biotek Elx808 Manual The easiest way to do this is to “scale to high well” if you have a known positive control or “high standard” on your plate. Biotek Error Codes A blank is not required if using a blank plate which is subtracted from the assay plate.
We'd like to decrease overall utility bills by all means possible. http://jamisonsoftware.com/error-codes/fp-t-1000-error-codes.php a) To prevent damage to the reader or PC, always turn OFF the reader or the PC before removing or inserting a serial cable. For convenience, a recommended adapter (P/N 75104) can be ordered directly from BioTek. The AutoPrime parameters (such as the interval and prime volume) can be set from DEFINE: EDIT: PRIME: AUTOPRIME. Biotek Plate Reader Elx808
After installing a known good cable, reboot the PC, then the reader, then launch the software. The USB connection will show up as a COM port in Windows Device Manager. This would also extend the lamp life. Source There are several other HP printer models that can be compatible via this adapter.
Both software packages meet the security and audit requirements of 21 CFR Part 11 to aid in your laboratory’s compliance programs Is it possible to pre-heat the incubator and warm up P/N 6002072 is a PCR tube holder designed to fit MS Research tubes P/N MSP-9601. What is the MSDS information for BioTek QC test solutions?
For readers with keypads, confirm the Baud rate under the utilities-setup menu (see Operator’s manual). Lidded plate handling requires the use of LHC2 (v2.16.9) with keypad instruments. It depends on factors such as the read type and plate type and OD of the measurement. AutoPrime is a feature on the EL406, ELx405, ELx50 and MicroFill liquid handlers.
What’s the best way to handle assays with temperature control? Can I transfer and share protocols between my BioTek washers and dispensers? Model Number: FLx800 Web Address: www.biotek.comThe FLx800 Multi-Detection Microplate Reader combines excellent specifications and performance with convenience and ease of use. have a peek here Choosing the right microplate for your assay is critical.
You will not have the ability to validate steps that require a reader (such as “minimum interval” setting in a kinetic read), but otherwise, the software is fully functional. Sample readings should be > 5000 RLU. If there is an error upon startup, press “stop”, record the error code and press “main menu”. Yes. 998 nm provides a correction wavelength that is not temperature sensitive.
AutoPrime is a feature on the EL406, ELx405, ELx50 and MicroFill liquid handlers. Most of our readers have a maximum of 99,999 counts, so a good target for the high well is 80,000. Remove the filter in the emission filter wheel in position 1, position 4 is the second best choice (NOT position 2 or 3). 7. Please try the request again.
Thus at very high ODs a variation of 0.1 OD is only a count of signal or less. Generated Fri, 14 Oct 2016 10:36:27 GMT by s_ac4 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.6/ Connection You may download and install the proper USB driver from this link (http://www.ftdichip.com/Drivers/VCP.htm). If you are using Gen5 software, the tungsten lamp can be powered ahead of time so that it is ready for reading a plate without waiting for warmup.
The system returned: (22) Invalid argument The remote host or network may be down. Close the door and turn on the power on the instrument. 10. Will my ELx808 or PowerWave 340 work with plates that are not 96-wells? Your cache administrator is webmaster.
For nonaqueous solutions, the Bio-Cell can provide a 1 cm reference value for pathlength correction. If you are using a USB cable or USB/serial adapter, you must install the proper USB driver. How do I transfer Gen5 to a new computer? Bacteria multiply rapidly in solutions containing proteins (serum) and sugars.
Fluorescence Readers What are the benefits to Top Reading versus Bottom Reading on my fluorescence microplate reader?