FL = Flow. One sensor has detected 118º F at heater. Spa has shut down. Problem is - there's not much consistency among the error codes used by spa pack manufacturers. http://jamisonsoftware.com/error-codes/gecko-spa-flo-error.php
SnH Hi Limit circuit open or faulty SnS Sensors out of balance, reporting different results SnT Temperature sensor fault, circuit open or faulty SP-F1,F2 or F3 Fuse 1,2 or blown SP-HR Heater is shut down, but other spa functions run normally. hot = Overheating, water over 112° F. Ecn = Spa operating in Economy Mode.
The equipment stays on until the sensors detect that the spa temperature has risen to within 20 degrees of the set temperature. Low speed pump and heater will activate until spa reaches 65ºF.OH = High temperature condition, has reached 110ºF. dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). Check for proper spa water level and ensure pump is primed.
PSoC : Pressure switch open with circulation pump. Find more hot tub / spa parts at Spa Parts Zone.You can also shop for Pools, Spas and Supplies at Amazon. The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. Marquis Spa Error Codes Brett Spa Side Error Codes OH : Temp exceeds 118 degrees Fr : Freeze condition - temp below 40 degrees FL : Pressure switch failure EO : Shorted temp sensor E1
Touch any button to reset the system. Hot Tub Error Codes If alternating with temp, may be temporary condition. Pump may also be deactivated). http://www.spatecservice.com/error-codes-digital-or-blinking-indicator-light.html Hold = Panel sensors have been pressed too many times in a short period of time.
The fundamental reason is water flow through the spa control system, if the water is not flowing at a rate to satisfy the switch, it will result in one of the Balboa Spa Control Manual The first thing to do is shut the spa down, remove the filter and make sure all the jets are open. For more information regarding Balboa tech support click here Gecko Spa Side Error Codes FLO : Pressure switch failure, switch open FLC : Pressure switch failure, switch closed Prr : Temp If display shows only this message (blinking) spa is shut down.HFL = Substantial difference between temperature sensors detected.
Generated Mon, 17 Oct 2016 04:55:04 GMT by s_wx1131 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection http://www.hottubworks.com/blog/spa-error-codes-the-big-list/ Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). Gecko Spa Pack Troubleshooting Spa unusable. Balboa Hot Tub Error Codes Is it an Error Code, or a System Status Code?
FLO = Flow Switch (heater is deactivated. http://jamisonsoftware.com/error-codes/flx800-error-codes.php Heater disabled but the spa is operational. Switch closed while pump is deactivated. Do not enter the water. Vita Spa Error Codes
I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct. Check for clogged filter FL2: Pressure switch problem. website and have your pool and spa / hot tub supplies and replacement parts shipped to you? Check out these International Package Forwarding Options. * Edwin's List is an independently owned and my review here Status of the heater element is unknown.
If flashing by itself, spa is shut down. Gecko Hot Tub Troubleshooting Switch closed while pump is deactivated COL: Cool condition. Spa has shut down.
Please try the request again. SL = Sleep mode Brett Aqualine Control Systems for Spas or Hot Tubs: OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° FFL = Pressure switch ICE = Freeze protection. Coleman Spa Error Codes The Spa or Hot Tub Panel Displays: SL This indicates the system is in sleep mode and can be changed by pressing the up temp.
Spa is shut down. drops hot: water over 112° F. If display shows only this message (blinking) spa is shut down. http://jamisonsoftware.com/error-codes/fortran-90-error-codes.php Pressure switch is not working.
IC, ICE, ICE2 Freeze Condition detected; Warm up procedure begins. Product endorsement is not implied unless specifically noted.