Gene. AnneJ, October 24, 2012 i know that it can be very difficult to have issues with your range. characters left:
Thank you! If the sensor checks no continuity, an "OL" reading on this meter, it should also be replaced. F1 or F10 - Runaway temperature. Can you please tell me, does this sound like a bad control board?
Thank you in advance, Steve Gene // May 16, 2015 at 6:25 pm Hello SteveB, You may want to check the wires between the temperature probe and the EOC. I was able to clear the lock and the oven gave an F1 code. i hope this helps. SO PLEASE WRITE ME BACK AND HELP ME!!!!
Thank Mike, you've been very helpful! It's possible that your range is not heating to the temperature that you set it to, or the control board may be reading the temperature incorrectly. This time the relay board will likely need to be replaced again but where last time the fault was visibly on the board, this time the burn was on the pins Frigidaire Oven Error Codes Per your description the temperature sensor checks OK.
If there is a such part, replace it. Frigidaire Oven F10 Reset You may want to start the troubleshooting from checking the temperature probe for continuity, using a multimeter. Ask a Technician for Answers ASAP Ask an Expert Home Improvement Questions Appliance Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help If there are no relays on the EOC, check the parts list (Search by the Model number) for the relay or power board.
Thanks for watching. Frigidaire Rtd Sensor Mike Ask Your Own Appliance Question Customer: replied6 years ago. if you need further assistance, please reply to this thread. I REALLY NEED IT FIXED Gene // May 19, 2015 at 11:05 pm Hello Christy.
You may want to start the troubleshooting from testing the temperature probe (sensor). she gets error code 11. Frigidaire Oven F10 Beeping Jim // Dec 8, 2014 at 1:00 pm Hi Gene. What Does F10 Mean On A Frigidaire Oven Your question was published, help is on its way!
Actually it is always the safest way. this content The keypad would not stop beeping and flashed an F11 code. If you would like to replace it too, I need one more letter from the model number to get the correct part number for you. Learn More for questions or assistance, call 1-800-252-1698 (Se Habla Español) M-F 6:30 a.m. - 10:00 p.m. Frigidaire Eoc
Ok basically what the F10 is telling you in this case is the oven is over heating. Your stove is new and suppose to be covered under manufacturer warranty. Parts cat. weblink Is it safe to use the range top or should we leave the breaker off for the weekend until we can get a tech on Monday?
Press UPPER OVEN or LOWER OVEN to select oven. 2. Frigidaire Stove F11 Error Gene. Gene.
Gene // Mar 29, 2015 at 6:41 pm Hello MML, Sorry for the delay. Diese Funktion ist zurzeit nicht verfügbar. It did it twice using the oven and broiler. Frigidaire Stove F1 Error Gene.
Very new range. Unfortunately (fortunately for your wife =-D) this part has been discontinued and is no longer available. What part do I need to replace it 2 answers Popular Products in Ranges Range Kleen Replacement Drip Pan 2 pack - ... http://jamisonsoftware.com/frigidaire-oven/frigidaire-oven-error-code-f1.php Our cooking manuals cover a wide selection of gas and electric models of ovens and cook tops, ranges and stoves, self-cleaners and convection ovens.
Appreciate any help! After much reserach I purchased a new EOC part # 316462861 which arrived today and I immediately installed it. Most likely the problem is a faulty EOC. If oven continues to overheat when the power is reapplied, replace EOC.
Sorry for the delay. Gene. We will proceed further. Wards Npa Electric trimmer Model #1100 was saved to your profile.
If the problem persists, replace the EOC. Mike Gene // Jun 6, 2015 at 10:30 pm Hello Mike, Thank you for your question. I'll be glad to help you if any problems with the diagnostic. Thank you for your question.
I have replaced the eoc and the temp sensor. The normal reading at the room temperature is supposed to be about 1100 Ohms. Let me know the result. Check wiring of lock motor, lock switch and door switch circuits.