I decided just to keep the range unplugged until the new EOC is installed. So we were back to blaming the EOC. I would recommend to eliminate the sensor plug and splice the sensor into the wire harness using a high temperature wire nuts. Valerie Gene // Dec 19, 2014 at 11:42 am Hello Valerie, Sad story. http://jamisonsoftware.com/frigidaire-oven/frigidaire-f10-error-fix.php
Parts Questions & Answers Questions & Answers about this model powered by F10 Error code on my Frigidaire glass top stove Model number fefl79gca. The problem has worsened as now the PF code will come up whenever the oven (bake/broil) is selected. You also may want to do the following troubleshooting: Unplug the range. The new one should solve it.
A code never flashed on the screen. When did you install a new EOC? The part number for the EOC 316455410 Thank you for your question. Sprache: Deutsch Herkunft der Inhalte: Deutschland Eingeschränkter Modus: Aus Verlauf Hilfe Wird geladen...
Thanks so much Jacqui Gene // Jan 4, 2015 at 11:59 am Hello Jacqui, My answer is Yes. note: disconnect the power cord from the power source before servicing your range. If the oven is overheating, this can be caused by a stuck relay or contact on the oven electronic control board. Frigidaire Oven Error Codes Gene // Apr 6, 2015 at 9:53 pm Hello John, Thank you for your question.
THANK YOU AND HAVE A GREAT DAY!!! Frigidaire Oven F10 Beeping Crystal // Mar 17, 2015 at 7:45 pm Hello, I have a Frigidaire Model#FGF337ABJ. You can get it from AppliancePartsPros.com for $558.91. Gene // Nov 21, 2013 at 3:17 pm Hello Dave.
If fault returns after reconnecting power, replace the EOC. Frigidaire Rtd Sensor If there are no relays on the EOC, check the parts list (Search by the Model number) for the relay or power board. Check for shorted Sensor Probe harness between EOC & Probe connector. I do have several boards.
The normal reading should be about 1100 Ohms at the room temperature. Keep me posted. Frigidaire Oven F10 Reset If this error code shown while the oven was in day time mode, the EOC would need to be replaced. What Does F10 Mean On A Frigidaire Oven OK, Continue Tips for finding your unique model number Look for your model sticker, tag or plate.
Most likely the problem is a faulty EOC. have a peek at these guys shows clock/temp board, is this the EOC ? Thread Tools Show Printable Version Search Thread Advanced Search Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode October 5th, 2010,08:49 PM #1 Roccobon View Profile View Forum Severe overheating may require the entire oven to be replaced should damage be extensive. Frigidaire Eoc
The author of this site has no liability for errors, omissions, or any defects whatsoever in the information or instructions, or for any damage or injury resulting from the utilization of Keep me posted. Check for continuity between the two probe wires. check over here The part number for the porcelain wire nuts (pack of 10) AP3440631 Good luck.
Thus the question is : are you really like this range and going to keep it or you will replace it as soon as the control panel will die? Frigidaire Stove F11 Error the oven temperature sensor can be removed and tested for resistance and compared to the rtd scale in the image below. Can you tell me what could be causing this error code and what parts I'll need to replace?
RTD Sensor Probe is your oven sensor probe, ohm that with the range unplugged, should read 1100 ohms at room temperature. Severe overheating may require the entire oven to be replaced should damage be extensive. 2. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power.3. (F11, 12 & 13) Larry Smith // May 20, 2015 at 11:05 am Hi Gene, I have an F10 on a PLEB30s9dca Fridg. Frigidaire Stove F1 Error Ask a Technician for Answers ASAP Ask an Expert Home Improvement Questions Appliance Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help
if the oven temperature sensor tests okay; the electronic oven control will need to be replaced. The user interface board is mounted on the back of the range, just below the control panel. Usually an hour or so after it has been shut off. this content Severe overheating may require the entire oven to be replaced should damage be extensive. 2. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power. 3. (F11, 12 &
Gene // Dec 18, 2014 at 7:58 pm Hello Jim, Sorry for the delay. Phil.