Neil Gene // Apr 5, 2015 at 9:46 pm Hello Neil, Thank you for your question. Gene // Jan 3, 2015 at 7:48 pm Hello Sharon, Sorry for the delay. If this error code has been shown while the oven was not cooking then the EOC would need to be replaced. I would recommend to eliminate the probe plastic connector and just splice the wires using a high temperature porcelain wire nuts. weblink
The black potentiometer should have a resistance of 10KΩ (± 10%). I decided to pull off the rear cover and take a peak and found a portion of the Oven Control Board was burnt/charred. My wife was doing some Xmas baking and set oven to 350 and about 10 minutes into the baking the oven started beeping and the F8 code came up. Is there a way to calibrate it?
LinkBack Thread Tools Search this Thread Display Modes #1 (permalink) 09-01-2010, 07:49 AM fyrdman Junior Member Join Date: Sep 2010 Posts: 1 F30 troubleshooting details Model Number: ples389eccBrand: Can you please tell me, does this sound like a bad control board? Thank you, Gene. Gene.
I bought laser thermometer for the oven and it would verify the lower temperature. Also, just a side note I have purchased various parts from appliancepartspros.com over the years and have always been very happy, top notch business. Frigidaire does not sell such harness but you can find a similar wires in a local electric or hardware store. Frigidaire Oven F10 Beeping Thank you for your question.
If you measured at the probe, an open (infinite resistance) or short (zero resistance) indicates a bad probe. Frigidaire Oven F10 Error Keep me posted. Gene. To check the probe, disconnect power and either pull the probe from the cavity of the oven (two screws, and a disconnect plug) and measure resistance across the probe, or take
The temperature sensor part number 316217002 The relay board part number 316429800 This part is on back order. What Does F10 Mean On A Frigidaire Oven All rights reserved. © Applianceblog.com 2004 - 2014 Login|Contact Us Appliance Need Appliance Repair Help? Ed Gene // Apr 23, 2015 at 9:29 pm Hello Ed, Thank you for your question. Locate the temperature sensor (RTD) plug on the control board (EOC).
I did this and it didn't work. The part number for the EOC is 316443865 Good luck. Frigidaire Stove F11 Error In regards to my Electrolux Icon electric wall oven E30EW75GPS1 In addition to the broiler coming on all by itself and this overheating the oven, we also noticed sometimes during baking Eoc Frigidaire Oven If the error code shown on your oven display leads to a possible problem with oven temperature sensor, start the troubleshooting from testing the temperature sensor resistance.
Thank you Gene // Nov 5, 2014 at 11:41 pm Hello Frank, Thank you for your question. http://jamisonsoftware.com/frigidaire-oven/frigidaire-oven-error-codes-f1.php Actually it is always the safest way. As soon as you remove the rear panel the board should be visible. sensor??? Frigidaire Oven F10 Reset
ft. ... Ugly is the new Sexy! I managed to push them back into the cap, and we were able to reconnect it to the EOC board, but at least one of them broke off. http://jamisonsoftware.com/frigidaire-oven/frigidaire-oven-error-codes-f10.php Valerie // Apr 24, 2015 at 7:00 am Hi Gene, I am having problems again and before I order on my diagnosis, I wanted your confirmation.
Check the lock motor and the switches for continuity. Frigidaire Rtd Sensor Good luck. Select Model Number Part Number Enter your model or part number Search Can't locate your model number?
Check wiring in probe circuit for possible open condition. Use our finder Choose your product type Select Select Cooktops Dishwashers Dryers Freezers Microwaves Ovens Ranges Refrigerators Washers Common model number plates Plate location Common model number plates View sample model Gene // Apr 6, 2015 at 9:53 pm Hello John, Thank you for your question. Frigidaire Stove Keeps Beeping It is just run away heat.
Why wouldn't the whole burner quit? Small silver rod.applianceguy : Remove the screws and pull out through oven. Generated Sun, 16 Oct 2016 02:43:12 GMT by s_ac15 (squid/3.5.20) this content Gene.
I read that you could try to cut the power to the range for a little while and see if the range would reset. Ask a question Get up to 45 % off On Ranges Related Questions Related Questions'>What does the fault code F9 & F1 indicate on my Frigidaire gas range? 1 answer Related I checked the sensor and it's 1102. F62 Missing zero-cross signal Replace the EOC.
If you would like to replace it too, I need one more letter from the model number to get the correct part number for you. I got the code f11 and it won't stop beeping. It is a lot of money but the worst part of it is that usually manufacturers will stop to make them in a few years after they made such model. The best way to do it is to pull the range out of the wall.
Also the model number you posted is incomplete. Thank you for your question. After much reserach I purchased a new EOC part # 316462861 which arrived today and I immediately installed it. CT Sun 7:30 a.m. - 9:00 p.m.