Remove the range rear panel and disconnect the probe plug. Check lock switch for proper operation ( do they open and close, check with ohm meter ). Thanks! Appreciate any help! weblink
The part number for the EOC is 316560118 You can order it by clicking on the part number. If clear key does not eliminate problem, turn off power for 30 seconds, then turn on power. Ed // Apr 27, 2015 at 11:01 am Hi Gene, Per your suggestion, I cut the 2 violet wires (the 2 running between the EOC and the RTD temperature sensor) and All Electronic Oven Controls (EOC) have ability for self diagnosis.
what does the f10 code mean on a frigidaire oven? Report This by Manage My Life December 24th, 2010 Frigidaire Electric range, model no. Gene // Apr 1, 2015 at 8:35 pm Hello Steve, Thank you for your question. Most likely the problem is a faulty EOC.
The part number for the EOC is 316557115 Good luck. Turn off power for 30 seconds then turn power on. Good luck. Frigidaire Oven Error Codes Gene // Dec 24, 2014 at 1:10 pm Hello Craig, It is not difficult to do it but, for more accurate advice I need the complete model number of the oven.
If the error code shown on your oven display leads to a possible problem with oven temperature sensor, start the troubleshooting from testing the temperature sensor resistance. Frigidaire Oven F10 Beeping Check the upper oven temperature sensor by measuring resistance between two wires connected to the pin 9 and 10 at the plug P27. She noticed the oven was cooking very hot. Ed Gene // May 6, 2015 at 9:35 pm Hi Ed, Put everything back together and give it a try.
You may want to start the troubleshooting from checking the temperature probe for continuity, using a multimeter. Frigidaire Rtd Sensor Sorry for the delay. You may want to replace it together with the overlay. I checked the sensor and and it checked at 1100.
Share it! Gene // Nov 30, 2014 at 4:31 pm Hello Martha, I will be more than glad to help you and your lovely mother! Frigidaire Oven F10 Reset In other words, is the problem w/ just the oven or w/ the range on top as well?esequiel walker :Just don't use the oven and you are fine with the range What Does F10 Mean On A Frigidaire Oven Remove the rear panel and locate two small power supply boards right next to the oven relay board.
Remove the rear control panel cover. http://jamisonsoftware.com/frigidaire-oven/frigidaire-oven-error-codes-f1.php There suppose to be one more letter. Locate the two pins in the plug at the EOC that are connected to the sensor. CT About Us Sears Commercial Parts Contact Us All Brands Parts Store Locations Top Parts All Categories Affiliate Program Appliance Parts Refrigerator Water Filters Lawn Mower Parts Snow Blower Parts Join Frigidaire Eoc
The instructions on how to adjust the upper or lower oven temperature usually are in the Owner Guide. This part is usually located on the back wall in the upper part of the oven cavity but it can be easy tested from the EOC. Where did you get the EOC you replaced recently? http://jamisonsoftware.com/frigidaire-oven/frigidaire-oven-error-codes-f10.php Page 1 of 2 12 Last Jump to page: Results 1 to 10 of 14 Thread: [FIXED] error f10, shut breaker off now oven normal?
If the fault returns, replace the keyboard ( membrane ). Frigidaire Stove F11 Error Is there anything internal to the oven where we could turn off the appliance?esequiel walker :No just unplug it. Thanks again.
Thank you! It is located behind the control panel. Gene // Mar 15, 2015 at 7:12 pm Hello Robert, Sorry for the delay. F10 Error Code Kenmore Oven Connie // Jun 17, 2015 at 5:22 am Have a GLES389ESD Frigidaire Slide in stove.
Du kannst diese Einstellung unten ändern. Denise // Jun 15, 2015 at 1:38 pm Hi, Gene, I have a PLEs39ECG, serial NF73726 that gives me an error F30. Is it me or do I have two bad EOC's? this content The EOC part number is 316418708 You can order it by clicking on the part number.
If oven continues to overheat when the power is reapplied, replace the EOC. Thank you for your question. What was wrong with the old one? I was not aware of a door lock (because I don't see anything to slide) other than the "lock" symbol on the control panel that I've never used… Can you tell?
If this error code shown while the oven was in day time mode, the EOC would need to be replaced. Valerie Gene // Sep 7, 2015 at 9:06 pm Hello Valerie, Thank you for your question. In this model the keypad is a part of the EOC. And if so, can you please help me identify the correct part to order on your website?
Gene // May 10, 2015 at 9:44 pm Hello Sally, I'm sorry for the delay. Keep me posted. Melde dich bei YouTube an, damit dein Feedback gezählt wird. Add your answer Sign in to answer a question 2 Answers from these members: The temperature sensor is within the proper range. The answer James R sent has the correct information