Frigidaire used the name RTD sensor or RTD probe, where RTD means "Resistance Temperature Detector" instead of oven temperature sensor. The correction for this problem is to replace the EOC. Could the oven control data be used to verify these failures, maybe downloaded by a tech ? Pull off the face. http://jamisonsoftware.com/frigidaire-oven/frigidaire-oven-f31-error.php
If the igniter glows but the gas doesn't flow, possible the igniter itself is to weak to open the gas safety valve. Can you suggest a fix for this? Gene // Mar 15, 2015 at 6:56 pm Hello Rachel, Thank you for your question. The t/stat you need to reset looks just like the one on the back.
Error codes can often be resolved by removing power to the appliance for a minute and then restoring the power. Gene. The wiring harness resistance indicates no connectivity (the purple wires coming from the EOC). ft. ...
NOTE: OEC may initially display an F10 thinking a runaway condition exists. Gene. Check lock switch for proper operation ( do they open and close, check with ohm meter ). Eoc Frigidaire Oven If the motor does not rotate, replace lock motor assembly.
Thanks, Gene // Sep 7, 2015 at 9:26 pm Hi Jay, Thank you for your question. Frigidaire Stove F11 Error I have heard a few times what sounded like it shorting out from the control knobs on the right side. Prior to testing make sure that the shaft is set to the off position, disconnect the wire harness and use an ohmmeter to measure the resistance between pins 1 & 2 Code f10.
I have a used stove of the same kind just different color. Frigidaire Oven F10 Beeping Gene. Gene. In order to provide most accurate advice I need the complete model number of the oven.
If the reading is correct, test operation of the potentiometer by measuring the resistance between pin terminal G (center) and either of the outside pin terminals as the control shaft is Shorted Probe connection. 1. (F30 or F31) Check resistance at room temperature & compare to **RTD Sensor resistance chart. F10 Error On Frigidaire Oven The relay board is obviously much cheaper than replacing the range and I hate the environmental component contributing to a landfill but at what point do you throw in the towel Frigidaire Oven Error Codes Sounds like the EOC is the culprit.
Hound of Baskerville Mask $12.99(Retail $17.99) It was a huge, spectral black dog, which according to legend roamed the desolate moor to avenge its mistress's death....[Read More] Appliance Parts, Accessories & http://jamisonsoftware.com/frigidaire-oven/frigidaire-oven-f3-error.php Maximum oven door unlock attempts exceeded. Ken // Dec 25, 2014 at 7:12 am Hello Gene, Thank you for GLEFS77CSC is the model number I was able to clear the lock and the oven gave an F1 Gene. Frigidaire Oven Rtd Sensor Probe
If you would like to replace it too, I need one more letter from the model number to get the correct part number for you. You may want to order a new overlay if you would not be able to move the old one to the new EOC. They are identical. http://jamisonsoftware.com/frigidaire-oven/frigidaire-gas-oven-f10-error.php Thank you, Gene.
Good luck. Frigidaire Oven F10 Reset I have a frigidare oven that the oven stopped working.the broiler is stll working fine.i called an appliance tech and he told me the eoc is bad so i orderd one ft.
Or should a person stay away from Electrolux? If the sensor and wiring are good, the EOC would need to be replaced. Ask a question Get up to 50 % off On Wall Ovens Related Questions Related Questions'>Why does my oven turn off once it is preheated on a Frigidaire range model FEF366DCF? Frigidaire Oven F31 Error Thanks!
What Your Appliance Error Code Really Means. Most error codes are generated as a result of irregularities in the power supply or usage. BUT oven not heating up. this content Disconnect power, wait 10 seconds and reapply power.
Thank you for stopping by. Ken // Dec 24, 2014 at 4:00 pm Gene, Merry Christmas. Valerie, you posted your first question on the front page: http://www.askgene.com/ and I replied on the same page. If the problem persists, replace the EOC.
Unfortunately both parts have been discontinued and are no longer available. Replaced temp probe and same thing. The part number for the EOC is 316557115 The part number for the latch motor assembly is 316464300 Good luck. Thanks Larry Gene // May 20, 2015 at 3:07 pm Hello Larry.
Set of four chrome drip pans, 2 small, 2 large Item Number W10278125Thanksgiving is coming - Item # W10278125 RepairClinic.com also ships appliance repair parts to Canada!....to your home, The normal reading should be about 1100 Ohms at room temperature. kimberly // Feb 26, 2015 at 6:22 pm Hi I have a frigidaire gas oven model LFGF3014LBC and have been getting f10 error for a while and now just started getting Maximum oven door lock time exceeded.
Valerie Gene // Dec 19, 2014 at 12:58 pm Valerie, Looks like the problem is a faulty oven relay board. Is it safe to leave appliance unplugged for a few days. With this info. Great.
Gene // Dec 2, 2014 at 10:00 pm Hello Steve, Sorry to hear you have more problems with your range. Both probes check 1178-1179 OHMS at the probe and the board. I have replaced the EOC and the RTD, and still get the error code, what else could it be :(? Of the two in the back, one was model TX22, where the second "2" means that thermostat should be normally open and isn't on the same circuit as the therometer probe