I was able to use it a couple times after but the cooking times varied between a little slow and A LOT slow. Gene // Jul 9, 2015 at 2:26 pm Hello, Bessie. James // Dec 21, 2014 at 11:14 am hi Gene i have a frigidaire stove that is showing an f11 code. Check Sensor wiring harness between EOC & Sensor Probe connector. 2. (F30 or F31) Check resistance at room temperature, if less than 500 ohms, replace **RTD Sensor Probe. weblink
It would need to be replaced. Gene. I have spent lots of time researching my issue and can not find anyone else describing this particular problem. F11 - Shorted keypad.
My questions: 1. The time now is 06:22 PM. How's our diagnosis and where do we go from here? Eoc Frigidaire Oven You can get it from AppliancePartsPros.com for $558.91.
I found them for you: "Each oven temperature can be individually adjusted. Gene // May 10, 2015 at 9:44 pm Hello Sally, I'm sorry for the delay. Gene // Jun 18, 2015 at 4:36 pm Hello Denise. The wiring harness resistance indicates no connectivity (the purple wires coming from the EOC).
What does this mean please? Frigidaire Stove Beeping F10 Thank you for your question. The rapid preheat would report that the oven was heated but if you cancelled that and initiated any other regular (without rapid preheat) heating mode (convection, roast, bake) they would all BUT oven not heating up.
Gene. The part number for the EOC is 316557205 The part number for the overlay is 316419303 Good luck and keep us posted. Frigidaire Stove F11 Error If the reading at the sensor is the same as reading at the EOC plug, the sensor is defective. Frigidaire Oven Error Codes The black potentiometer should have a resistance of 10KΩ.
Unfortunately (fortunately for your wife =-D) this part has been discontinued and is no longer available. http://jamisonsoftware.com/frigidaire-oven/frigidaire-range-error-code-f30.php There are probably over 50 different error codes but in this article we will review only the most common ones. If the reading at the sensor is correct, the wiring between the sensor and the control is defective. Door would not release, funny smell, threw circuit breakers. Frigidaire Oven Rtd Sensor Probe
The broiler element runs non stop. Thank you for your question. In order to properly diagnose the problem you would need to unplug the range and pull it out of the wall. http://jamisonsoftware.com/frigidaire-oven/frigidaire-range-error-code.php CST Chat FREE Standard Shipping on orders of $ or more Purchase requirement calculated before taxes and shipping charges and after other discounts have been applied and must be made in
Gene // Mar 15, 2015 at 6:56 pm Hello Rachel, Thank you for your question. Frigidaire Oven F31 Error Valerie Gene // Sep 7, 2015 at 9:06 pm Hello Valerie, Thank you for your question. You may want to replace it as well.
Everything is visible here, so it will be apparent what to undo. Gene. When did you install a new EOC? Frigidaire Oven F10 Reset If that is ok then another can be checked up front.
Our other reason for blaming the EOC was the loss off other functions on the oven. The black potentiometer should have a resistance of 10KΩ (± 10%). I have a Frigidaire range, model #PLEF398DCH. this content Connie // Jun 17, 2015 at 5:22 am Have a GLES389ESD Frigidaire Slide in stove.
Press START to accept the temperature change and the display will return to the time of day. this is the 2nd time in 380 days that we are replacing the relay board. Thank you, Gene. Thanks Rich Gene // Mar 15, 2015 at 7:17 pm Hello Richard, Thank you for your question. "Day time mode" means the oven is off and the clock shows only time
In this range there are no a separate keypad. or Is it something else that's causing this problem? Try resetting the unit and see if the error code will clear. if you test the oven temperature probe and it tests good, the electronic control board may need to be checked to make sure it's communicating with the sensor.
The problem has worsened as now the PF code will come up whenever the oven (bake/broil) is selected. My question is this, would that be the main culprit? See Details Frigidaire FGEW2765PB Gallery 3.8 cu. The part number for the EOC is 316207529 Thank you for your question.
Thank you for your question. Is there a way to calibrate it? QUOTE=fyrdman;267408]I had the same issue as macao. The EOC part number is 316418708 You can order it by clicking on the part number.
Unfortunately both parts have been discontinued and are no longer available. Gene. What was wrong at that time? Remove the rear control panel cover.
Rick // Dec 25, 2014 at 7:23 am I have a Frigidaire model #GLEB30T9DBA double wall oven. The lower oven has no issues. Valerie // Apr 24, 2015 at 7:00 am Hi Gene, I am having problems again and before I order on my diagnosis, I wanted your confirmation.