Relay failed this check. Assemble it back and reapply power to the range. In such a case the wires may need to be cut and spliced together using ceramic wire nuts. I checked the sensor and it's 1102. weblink
Is it me or do I have two bad EOC's? Start the troubleshooting from verifying the resistance value of the potentiometer. What are your thoughts? If the reading is correct, test operation of the potentiometer by measuring the resistance between pin terminal G (center) and either of the outside pin terminals as the control shaft is
F6 No 60 Hz time base 60 Hz time base is required for time controlled cycling. Unplug the range and remove the rear panel. I have replaced it and it seems to heat up and bake now.What I am finding now is that an error code F5 comes up occasionally. Most oven sensors have a mounting plate that is attached to the rear wall of the oven cavity interior.
LOL) Gene // Dec 24, 2014 at 12:11 am Hello Len, This error code means the microprocessor has found the lock motor switches to be out of sequence or shorted. To start viewing messages, select the forum that you want to visit from the selection below. Thank you. Frigidaire Electronic Oven Control Top #277383 - 05/15/06 07:07 PM Re: Frigidaire oven error codes F3 & F2 [Re: jeff1] rdamuth newbie Registered: 05/15/06 Posts: 3 I believe that it is a REG74BL3.The EOC sounds
The part number for the EOC (aka a clock/timer) is 316418735 Good luck. Frigidaire Oven F1 Error I checked the RTD temperature probe at the plastic connector (1083 - 1100 ohms). The F3 for shorted probe should only occur when the oven is active or when you attempt to enter a mode. Gene.
Any ideas. Frigidaire Self Cleaning Oven F1 Error Is there a way to calibrate the EOC? The instructions on how to adjust the upper or lower oven temperature usually are in the Owner Guide. It is a Frigidaire Model # FFEF3048LS Any help appreciated!
It's self-adhesive and if it can not be safely removed from the old EOC and properly attached to new part, you may want to order the overlay as well. If less than 500 ohms, replace the oven temperature sensor probe. What Does F3 Mean On A Frigidaire Oven Thank you for stopping by. Frigidaire Microwave F3 Error Code Locate the P5 connector at the EOC and remove two violet wires from pins 12 and 13.
Per your description the reading at the EOC is incorrect while the sensor itself checks OK. http://jamisonsoftware.com/frigidaire-oven/frigidaire-gallery-wall-oven-error-codes.php In this model the keypad is a part of the EOC. There suppose to be one more letter. Replace the oven door latch motor assembly if necessary. Frigidaire Oven Temperature Sensor
Overnight or Rapid Shipping available to your home or office! If the reading is incorrect, the temperature probe would need to be replaced. Gene // Apr 1, 2015 at 8:35 pm Hello Steve, Thank you for your question. check over here All of our chat agents are currently assisting other customers.
If not, I understand that it is likely either the thermometer or the panel. Frigidaire Oven Keeps Beeping F1 The part number for the EOC is 316207603 The part number for the overlay is 316243301 Good luck. Gene.
josh // Apr 10, 2014 at 4:05 pm hello gene I have a Frigidaire PLEFMZ99GCC oven.. Gene. Good luck. Frigidaire Oven F2 Error Code Keep me posted.
Once power has been disconnected from the appliance (do NOT just rely on the controls being off!), the sensor mounting screws can be removed. Gene. __________________ Appliance Repair Expert in Orange County, California. Next, the control panel will need to be taken off in order to measure the ... this content We ordered both the parts, tried the EOC first, with no fix.
Locate the two pins in the plug at the EOC that are connected to the sensor. LinkBack Thread Tools Search this Thread Display Modes #1 (permalink) 02-08-2010, 08:38 AM k75super Junior Member Join Date: Feb 2010 Posts: 3 F3 error code on Frigidaire oven Can you suggest a fix for this? If it would not solve the problem, you always can return the part for full refund.
Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar. and then F1 error code would occur. I washed the surface of the stove earlier today and when I turned the oven on it shot a flame out where the heat and condensation come out on top. If this error code shown while the oven was in day time mode, the EOC would need to be replaced.