Make sure the memory shown on the printout matches the installed memory. Power printer off one to two minutes. If you cannot find anything jammed up or broken in the back of the printer,open the upper front cover of the printer and remove the toner cartridge. Error 939 RIP Communications Lost Controller Engine Communications Lost The controller board and the engine board cannot communicate with one another. news
Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers Make sure fuse is installed correctly, Verfy proper fuser is being used. If this isthe first time you have seen the error, turn the printer off. If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact.
See Duplex on page 2-16 Error 24 The defined paper size is too short to print data as formatted. If you need the correct part number, you can find it here. Replace with the correct printhead. Check AC power source for noise.
Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. Remove jammed media Error 90X Software Error Unrecoverable software error. Controller Board 2. Lexmark Fuser Replacement It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer.
Check fan connector and cable for loose or damaged connection. Scroll Down to your error code.... There was an error with the application. Works great and certainly solved the problem (as I expected it would). -Alan A.
Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed. 922.02 Service Fuser Error Check paper sensor flag for restricted movement or damage. Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. If this does not help or if thiserror appears every time the printer is powered on, you will probably need service on the machine.
The fuser is the main part of a printer maintenance kit. Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine. 920.06 Service Fuser Error If an open circuit, replace the lamp or fuser. Service Fuser Error Lexmark Printer Error 27 Envelopes/paper loaded are wrong size.
sorry for my writing. http://jamisonsoftware.com/fuser-error/fuser-error-50-4.php Check fan for binding or defective bearing - Replace Fan How did we do? Intterconnect Board Error 940-943 Color Machines Toner Metering Cycle failure CMKY cartridge 940 = Cyan cartridge 941 = Magenta cartridge 942 = Yellow cartridge 943 = Black cartridge Toner metering cycle Any help here would be appreciated too. Lexmark X654de Service Fuser Error
Turned out to be the (HVPS) High Voltage Power Supply. Perform fuser service check. Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. More about the author It can also be the LVPS (low voltage power supply) or a fuse in the power supply on some models.
If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. 122.02 Service Fuser Error Service errors 980 thru 984 < device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. > Remove jammed media Error 250 Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder.
Replace the Autocompensator Assy. Verify correct cable connections from the Engine board to the HVPS. Thank you for the speedy shipment and response. Lexmark Support Error 53 Unformatted or Defective Flash - Flash problem at POR or while attempting to write.
If this is an intermittent error, you may want to check how the printer is plugged in, even ifit has worked on this surge device for months. The transfer roller was caked with toner all over it. Jump to error 92X Some Lexmark printers have indicator lights which indicate by solid, blinking or off, an error condition. click site ERROR 22 The exit sensor was not unmade in time.