i think the instructions arent telling me something. Look for pinched wire. Replace sensor if found defective. Wird verarbeitet... click site
Yes indeed, we will get it figured out! Check Electronic Range Control (ERC) - Welded clean relay contacts. F6 Shorted temperature probe This code will occur if temp. Ask a Technician for Answers ASAP Ask an Expert Home Improvement Questions Appliance Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help http://products.geappliances.com/appliance/gea-support-search-content?contentId=16238
kelly, i read thru the manual and it does not offer the testing procedures you describe. Don't want to call a repair man unless I need to. Try turning the breaker off for at least 3 full minutes and turn back on if problem is still the same let me know and i will advise the next procedure.
You may refer back to this question for as long as necessary after rating, AT NO ADDITIONAL CHARGE, until your problem is resolved. Kelly, Appliance Technician Category: Appliance Satisfied Customers: I just wanted to see if the "FO" code would point to one possible problem. Melde dich bei YouTube an, damit dein Feedback gezählt wird. Ge Oven Sensor Also, do you have a exploded view of the cooktop parts and parts number list?
Credentials confirmed by a Fortune 500 verification firm. Ge Oven F9 Error If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. after oven runs for awhile.
Number 16 in the picture below.Attachments are only available to registered users.RegisterHere Attachments are only available to registered users.RegisterHereAttachments are only available to registered users.RegisterHere Attachments are only available to registered
Make sure the control panel ribbon cable is plugged into the control board slot tight and firm. Ge Error Codes Washer One question: why did you push and hold the bake button? If you would like to schedule a service appointment, please contact GE Appliance Service at 1-800-432-2737 or schedule a service appointment onlineGE Appliances does recommend turning the range or oven off If not, the control keypad would be suspect (but not absolutely guaranteed to be the cause).
Switch is normally closed and will open if area overheats due to fan not operating. UE - Unbalance switch error Unbalanced load is sensed three times during a spin operation. Ge Fault Codes Check wiring and test operation of switches. Ge Oven Error Code F2 It is in there, I will look it up and tell you what to test.
In order to fix it, the control panel has to be replaced. get redirected here The part you will need to replace is available below. Reply With Quote September 11th, 2014,11:16 AM #5 John King View Profile View Forum Posts Premium Member Join Date Apr 2013 Location Bristol, CT Posts 10 Hey Rick, So I am agreed...how long will you be around? F76 Ge Oven
F1 Stuck touch pad Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced. one question before i get started....is the "main" board the same as the "logic" board? so i will have to dismount the unit and start probing it? navigate to this website lol.
If code reappears, replace control Note: If all above check OK the F5 code can be a result of a momentary loss of power (Do NOT replace control or lock, check Ge Oven F0 Error Code Sensors and control boards can be purchased at AppliancePartsPros.com. If fault persists, replace main board and recalibrate inductive sensors.
You may have to register before you can post: click the register link above to proceed. Look for pinched wire. Replace sensor if found defective. Ge Oven Error Code F7 Remove four screws holding the ERC to the control panel.
Pushing CLEAR/OFF pad. 2. Check probe. Good luck. my review here i pulled up the TECH mode prior to removing the top last night.
They are wired to the connector at the factory. its replacement part is far more expensive than the controller i think.....i had a feeling the first expert was off base here... Expert: Kelly replied4 years ago. k, i used a new meter and got the needle to 40 on the skinny wires and pegged the meter on the thicker wires (four test points). Forum Forum Home New Posts FAQ Calendar Community Albums Member List Forum Actions Mark Forums Read Quick Links Today's Posts Appliance PartsAppliance Maintenance TipsApplianceBlog Home Advanced Search Forum Appliance Repair Talk