If you are sure that you have the correct microcode installed, it could be that your interface is software blocked. share|improve this answer answered Mar 12 '13 at 17:50 user168261 worked BUT docs say I should use Bridged Adapter only if Its in a different subnet. –user36582 Mar 12 To install the microcode, simply emerge sys-firmware/iwl3945-ucode: emerge -av sys-firmware/iwl3945-ucode or, respectively sys-firmware/iwl4965-ucode: emerge -av sys-firmware/iwl4965-ucode or, if you have a Intel Wifi Link 5100/5300 sys-firmware/iwl5000-ucode: emerge -av sys-firmware/iwl5000-ucode If you unless i can find a ebuild i cannot merge t to kernel. http://jamisonsoftware.com/gentoo-error/gentoo-error-interface-br0-does-not-exist.php
Why is water evaporated from the ocean not salty? Device 103b > Flags: bus master, 66MHz, medium devsel, latency 0 > > 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI > Bridge (rev 40) (prog-if Then I fixed it by removing /etc/udev/rules.d/70-persistent-net.rules What I see Now is eth0 interface is present. I've contacted them before about audio drivers. https://forums.gentoo.org/viewtopic-t-928662-start-0.html
If you need to reset your password, click here. Thx for the tip, modinfo was new to me. There can be many events which may have resulted in the system files errors. com [Download message RAW] dmesg says only: [email protected] ~ $ dmesg | grep -i firmware [ 0.099927] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored I already have linux-firmware in my system,
It is about a minute after (50 seconds, I counted ) that wlan0 shows up.Cheers. there is a makefile which does not run in ech of the driver folders. You can use udevadm to recreate the rules #udevadm trigger --subsystem-match=net Occasionally switching from ipw3945 to iwlwifi will not work because of some missing symlinks. netcfg does not automatically takeover existing connections.
m 0 l roodap 10 May 2013 14:40:08 dhcppc0 ramaswamy # lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex 00:01.0 VGA compatible controller: Advanced Micro Devices Device 103b Flags: bus master, fast devsel, latency 0, IRQ 43 Memory at feb44000 (32-bit, non-prefetchable) [size=16K] Capabilities:  Power Management version 3 Capabilities:  Express Root Complex Integrated Endpoint, MSI That seemed to get everything running on bootup. https://bbs.archlinux.org/viewtopic.php?id=103068 Thanks TomH 2013/10/2 Joakim Gebart
Device 103b > Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18 > Memory at feb4e000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > > 00:12.2 USB controller: RTNETLINK answers: No such file or directory SIOCSIFFLAGS: No such file or directory Could not set interface 'wlan0' UP [ ok ] * Starting wpa_cli on wlan0 ... [ ok ] I suspected what you say about dhcp and I guess thats what I'll try. m 0 l roodap 13 May 2013 06:49:01 ifconfig gives only the ethernet configuration iwconfig says sit0 no wireless extension lo no wireless extension eth0 no wireless extension m 0 l
Do you use an initramfs? http://gentoo.2317880.n4.nabble.com/Wireless-network-card-not-loaded-on-first-boot-after-shutdown-td125150.html no results. Device 103b > Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18 > Memory at feb4c000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > > 00:13.2 USB controller: I then reboot without changing or doing anything > else and the card works just fine. > > I get no error modprobing the driver in both cases, but only after
Please check with modinfo any options to switch off > (e.g. this page m 0 l ex_bubblehead a b D Laptop a b 5 Linux 18 May 2013 14:04:15 Did you emerge and configure wpa_supplicant? Afterwards, a successful authentication should be possible. eth0 AND wlan0?3a) Also have you removed all connections from your INTERFACES array in rc.conf?4) If yes to 3 and 3a, post your profiles here.Also, it would surely help to know
After I changed to "open system" the problem was solved. m 0 l roodap 13 May 2013 08:22:05 modprobe finds and loads rtl8723ae dhcppc0 ramaswamy # lsmod Module Size Used by fuse 52431 2 snd_hda_codec_realtek 48189 1 rtl8723ae 116535 0 rtlwifi Which BCM options do you have enabled in the kernel? -- Neil Bothwick If Satan ever loses his hair, there'll be hell toupee. get redirected here Device 103b > Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18 > Memory at feb4a000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > > 00:15.0 PCI bridge:
For further configuration follow the Gentoo Handbook. fails to add the ssid and psk but to my surprise iwlist scan gives me a lot of nieghbours' wifi modem address including mine. Same as first post?2) Are you trying to configure both your connections via the same daemon i.e.
am i totally offbase and its a configuration thing? it's fixed. :Sa good-old pacman -Syufixed it... PS please don't top-post, it is not welcome on this list. -- Neil Bothwick I am in total control, but don't tell my wife. TomH 2013/10/2 Neil Bothwick <neil [at] digimed> > On Wed, 2 Oct 2013 15:31:27 +0200, TomÃ¡Å¡ HÃ¡jek wrote: > > > I already have linux-firmware in my system, just put brcmsmac
With the passing of Thai King Bhumibol, are there any customs/etiquette as a traveler I should be aware of? They do reply. You do need to activate the correct option(s) in the kernel (and thus rebuild the kernel). http://jamisonsoftware.com/gentoo-error/gentoo-error-interface-eth0-does-not-exist.php randalleg View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by randalleg 06-14-2011, 12:25 AM #7 randalleg LQ Newbie Registered: Apr 2011 Posts: