Page 1 of 2 12 Last Jump to page: Results 1 to 10 of 16 Thread: [QUE] lftp PASSIVE mode error Thread Tools Show Printable Version Subscribe to this Thread… Display The FTP deamon I use allows me to set the ports for Passive Mode as well as the command port 21. It may be necessary to configure the firewall so that it runs the SyncBackSE/Pro application with "SYSTEM" settings:Allow IP In From Any to Any Where Protocol Is Anyinstead of "Trusted Application" Current directory is /home ---> PROT P <--- 200 Data protection level set to "private" ---> PASV <--- 227 Entering Passive Mode ---- Address returned by PASV is ignored according to http://jamisonsoftware.com/socket-error/general-error-socket-connect-failed-late-connection-refused.php
Verify that the destination IP address is correct. If you see an error log similar to the one below, in the Site Properties of the problem site, click the Type tab, then change the Data Connection Type to Use Yes, my password is: Forgot your password? Ubuntu Logo, Ubuntu and Canonical © Canonical Ltd.
Find out how you can reduce cost, increase QoS and ease planning, as well. Another possibility is that connection is blocked by a firewall. For a regular FTP session, either disable the firewall or anti-virus software or configure them to allow CuteFTP to establish an FTP session over ports 20 and 21. The FTP server is running.I am using a correct username/password/port.Basically everything is as it was yesterday, except that I now get the error.Suggestions for a fix would be most appreciated.ThanksMorgalEDIT -
ERROR:> Can't connect to remote server. Adv Reply October 25th, 2010 #5 pi3ch View Profile View Forum Posts Private Message 5 Cups of Ubuntu Join Date May 2009 Location Australia Beans 19 DistroUbuntu 11.04 Natty Narwhal What settings do I have to change to solve this? Ftp Errors And Solutions How many simultaneous connections have you set in the deamon to allow per IP?
Please see How can I list all open TCP ports and their associated applications? Ftp Socket Error Your own settings will vary. WSAETIMEDOUT (10060) 10060 is a connection-timeout error that usually appears when the client does not receive a response from the server for a specific command. http://support.2brightsparks.com/knowledgebase/articles/213469-common-ftp-errors-and-socket-error-messages Adv Reply October 27th, 2010 #8 pi3ch View Profile View Forum Posts Private Message 5 Cups of Ubuntu Join Date May 2009 Location Australia Beans 19 DistroUbuntu 11.04 Natty Narwhal
On the client side, if the connection is accepted, a socket is successfully created and the client can use the socket to communicate with the server. Socket Error 11001 Host Not Found Unable to connect. Tango Icons © Tango Desktop Project. If everything goes well, the server accepts the connection.
I could easily get directories list and CD to them. http://www.linksysinfo.org/index.php?threads/ftp-error-port-forwarding-problem.1305/ Create a password I agree to the Terms of Service Signed in as (Sign out) Close Close Sign in Sign in Sign up Cancel Technical Articles Information to include for technical What Is A Socket Error Outgoing connections can be affected by the presence of firewall or anti-virus software on the local computer or network connection. How To Fix Socket Error See the portprobe URL I posted in my first reply - just change the number at the end with the port number to probe the port you want.
You will NOT get any reply!!!FTP connection problems? http://jamisonsoftware.com/socket-error/ftp-winsock-error-connection-refused.php Currently I can connect to one but not the other even though I have been using both all day. Other common problems are: Can connect to the FTP server but when trying to choose the destination directory nothing happens for a very long time. Learn More. Ftp Connection Timed Out Could Not Connect To Server
This is a good method in determining the root of the problem. Current restricted directory is / ---> PBSZ 0 <--- 200 PBSZ=0 ---> CWD /home <--- 250 OK. Errors are the best teachers. 0 Back to top of the page up there ^ #15 ChrisB New Member Group: Members Posts: 6 Joined: 24-August 07 Posted 11 September 2007 have a peek at these guys i've set them open, but i have to configure the pasv ports somewhere, but i don't know where t045ty, Nov 22, 2004 #7 ImprezaDude Network Guru Member R] 227 Entering
Esquire, Nov 22, 2004 #6 t045ty Network Guru Member yes the port is open port 21 and 20 doesn't matter! Freeftpd Generic Error For Access Violation Either can block the ports needed to make a successful FTP connection to the remote server. this is normal ftp behavior __________________ [Sig removed by Administrator: Signature can not exceed 20GB] MxxCon View Public Profile Find More Posts by MxxCon 02-15-2005, 06:08 PM #3 karpath
All Rights Reserved. Was this article helpful to you? If you are using implicit SSL then you probably need to use port 990 instead of port 21. How To Fix Socket Error 10060 Using private data connection. [R] PASV [R] 227 Entering Passive Mode (x,x,x,x,11,53) [R] Opening data connection IP: x.x.x.x PORT: 2869 [R] Data Socket Error: Connection refused [R] List Error [R] PASV
server.domain.com). ERROR:> Failed to establish data socket. Maybe coincidence. _________________### BEGIN SIGNATURE BLOCK ###No support requests per PM! check my blog Socket Error # 10039: There may be a problem getting the IP address for the hostname.
Try temporarily turning off any firewall you are running. 10052 - Network dropped connection on reset. Consult the documentation or help file for your specific firewall or antivirus software product for instructions. Is the client being forced to connect at port 5190 instead of port 21? (e.g., ftp://ftpaddress.com:5190) Esquire, Nov 22, 2004 #4 t045ty Network Guru Member yes, i connect only on When applying changes to the PRTG Administration Tool, PRTG Windows Services must be restarted so the changes take effect.
Exchanging encryption keys...Session Cipher: 128 bit RC4TLS encrypted session established.PBSZ 0200 PBSZ=0USER xxx331 Password required for xxx.PASS (hidden)230 User xxx logged in.SYST215 UNIX Type: L8Detected Server Type: UNIXFEAT211-Extensions supported: AUTH TLS When running a profile that connects to an FTP server you may receive the following errors in the log file: Scan failed (-1): Read Timeout: The connection to the FTP server i found my mistake i forgot to use "force active mode to use this ip" so it was my lan ip that use in active mode. All rights reserved.