Top Of Page Show: Inherited Protected Print Export (0) Print Export (0) Share IN THIS ARTICLE Is this page helpful? HTTP Server could not locate the HTTP/TCP service. T... I've also tried Active and Passive modes in the client. this content
A socket operation encountered a dead host. WSA_INVALID_HANDLE OS Dependent Specified event object handle is invalid. Microsoft Internet Information Services Setup required administrator privileg... An example is using a broadcast address for sendto without broadcast permission being set using setsockopt(SO_BROADCAST).
User Action: Check the destination address you are using. The Windows function is indicating a lack of required memory resources. Try increasing the time-out value in the Global Options dialog box (Tools > Global Options > Transfer > Reconnect and resume in [ n ] seconds if nothing received ) to An operation was attempted on something that is not a socket.
Thank you for your feedback! The server was unable to open ODBC Data source name , Table: name , under... Many thanks. Socket Error 10061 Connection Refused A message sent on a datagram socket was larger than the internal message buffer or some other network limit, or the buffer used to receive a datagram was smaller than the
Establishing an FTP Connection from the Command Prompt Firewall and Router Setup Using cscript.exe on 32-bit or 64-bit systems On a scale of 1-5, please rate the helpfulness of this article SSL/TLS error - 0, SSL error - 5, error:00000005:lib(0):func(0):DH lib Winsock error 10054 (An existing connection was forcibly closed by the remote host. ) SSL Connection not established I had the You may also want to be sure you are using a passive connection. socket is not listening).
Unable to write to filename, it is read-only or opened by someone else.... Error Code 10060 Socket Connection Failed Verify that you are connected to the Internet. The requested protocol has not been configured into the system, or no implementation for it exists. Clear search results Contact support Knowledge Base Frequently Asked Questions47 articles Sales15 articles Technical Articles426 articles Web Store9 articles Legal6 articles Education and Non-Profit3 articles All articles 2BrightSparks Homepage 2BrightSparks Homepage
The Data Source Name (DSN) may be incorrect. news WSAETIMEDOUT (10060) 10060 is a connection-timeout error that usually appears when the client does not receive a response from the server for a specific command. If you are using a router, verify the router is up and running (check by pinging it and then ping an address outside of the router). WSATRY_AGAIN 11002 Nonauthoritative host not found. Socket Error 10060 Connection Timed Out
Too many open sockets. If you continue to receive the same error after insuring ports 20 and 21 are open, contact the administrator of the site you are trying to connect to. WSAEHOSTUNREACH 10065 No route to host. have a peek at these guys This could happen with a call to another function later, including connect, listen, WSAConnect, or WSAJoinLeaf.
This could indicate a serious failure of the network system (that is, the protocol stack that the Windows Sockets DLL runs over), the network interface, or the local network itself. Error Code 10060 Connection Timeout The data is the e... This normally results from an attempt to bind to an address that is not valid for the local computer.
This documentation is archived and is not being maintained. For more information see GlobalSCAPE Knowledge Base Article #10384. No administerable services found.... Socket Error 10061 Connection Refused Windows 7 WINSOCK Error: Address already in use....
Usually the manufacturer of the device or software will also have specific instructions available on their Web site. Microsoft World Wide Web Publishing Service is running. Please enter a number between number and number.... http://jamisonsoftware.com/socket-error/ftp-winsock-error-10035.php Not logged in: The username and/or password is not correct.
WSAECONNREFUSED (10061) 10061 is a Connection Refused error sent to you by the server. Microsoft Catapult Access Gateway Service is running. COMMAND:> PASV 227 Entering Passive Mode (xxx,xx,xxx,xx,x,xxx). WSAENETRESET 10052 Network dropped connection on reset.
Error connecting with SSL: The FTP server does not support SSL, or you are using implicit SSL and it only supports explicit, or the wrong port number is being used. The data is the error. ... A protocol was specified in the socket function call that does not support the semantics of the socket type requested.